Answer:
The answer is "[tex]\bold{ 259.2 \times 10^{11} }[/tex]".
Explanation:
The amount of kilograms, which travel in a thick sheet of hydrogen:
[tex]M= -DAt \frac{\Delta C}{ \Delta x} \\\\[/tex]
[tex]D =1.0 \times 10^{8} \ \ \ \frac{m^2}{s} \\\\ A = 0.20 \ m^2\\\\t = 1\ \ h = 3600 \ \ sec \\\\[/tex]
calculating the value of [tex]\Delta C:[/tex]
[tex]\Delta C =C_A -C_B[/tex]
[tex]= 2.4 - 0.6 \\\\ = 1.8 \ \ \frac{kg}{m^3}[/tex]
calculating the value of [tex]\Delta X:[/tex]
[tex]\Delta x = x_{A} -x_{B}[/tex]
[tex]= 0 - (5\ mm) \\\\ = - 5 \ \ mm\\\\= - 5 \times 10^{-3} \ m[/tex]
[tex]M = -(1.0 \times 10^{8} \times 0.20 \times 3600 \times (\frac{1.8}{-5 \times 10^{-3}})) \\\\[/tex]
[tex]= -(1.0 \times 10^{8} \times 720 \times (\frac{1.8}{-5 \times 10^{-3}})) \\\\= -(1.0 \times 10^{8} \times \frac{ 1296}{-5 \times 10^{-3}})) \\\\= (1.0 \times 10^{8} \times 259.2 \times 10^3)) \\\\= 259.2 \times 10^{11} \\\\[/tex]
hi guys can u help me?
Answer:
3. have known
4. wrote
5. not sure
6.have changed, has only
7. answered
8. have missed
9.has never seen
10.never saw
11.became,have changed
12. have changed, have grown
13.was,found
14. was never
am not sure but hope it helps
which is one of the most important steps to do before you go into an interview ?
Research the company
Tell your current boss
Buy a new dressy outfit
Finish school
Answer:
Research the company
Explanation:
It is a good idea to find out information about the company you are interviewing. Among other things, this will help you decide if you actually want to work for that company.
Telling your current boss can be risky to your job. A new outfit may be helpful for certain positions--especially those where manner of dress is important. Finishing school may or may not be an important requirement for the position you're seeking. Your company research will tell you.
Researching the company is one of the most important steps to take.
Create an array of 10 size and assign 10 random numbers. Now find the sum of the array using for and while loop.
Answer:
10
Explanation:
6. Question
Which statements are true about routers? Check all that apply.
A router can only send data to another computer that's on the same network.
A router is a set of components that makes up computer networking.
A router connects devices together and helps direct network traffic.
A router utilizes network protocols to help determine where to send data packets.
7.
Question
Answer:
Check the 2nd, 3rd and 4th statements.
Explanation:
The router provides two basic functions traffic management between these networks through the transmission of data packets to the designated IP address, and the use of the same Internet connection by many devices.
A networking device is a router that transmits data packets between computer nets. Traffic control functions are executed on the internet via routers. Data sent via the internet are in data packets, for example, a web page or email.A router is a device connecting two or more packets or subnetworks. It is used to sets the components from the networking of your computer.Therefore, the final answer is "the second choice".
Learn more:
brainly.com/question/2162586
What makes a particular sector of the residential construction market dependent on globalization?
its need for innovation to spur growth
its embrace of renewable and sustainable technology
its commitment to multiculturalism
its requirement of labor or materials from far-flung sources
Answer:
its requirement of labor or materials from far-flung sources
Explanation:
"Globalization" generally means having or creating sources of supply in foreign countries, usually those with lower labor or material costs. If some industry sector is dependent upon that, then it's probably because it depends on labor or materials from low-cost sources.
what is the IMA of a fixed pulley
Answer:
Not sure
Explanation:
Looking now
All of the following are common causes of low engine compression except for
A. too much oil
B. defective valves.
C. weak piston rings.
D. bent pushrods
Answer:
B
Explanation:
Over filling of oil on an engine will not cause loss of compression. The crankshaft splashes it inside the engine and will come out the dip stick tube and breather on valve cover and it may splash up to the bottom of the pistons and force oil to the top through the rings
Given int variables k and total that have already been declared, use a do...while loop to compute the sum of the squares of the first 50 counting numbers, and store this value in total. Thus your code should put 1*1 + 2*2 + 3*3 +... + 49*49 + 50*50 into total. Use no variables other than k and total.
Answer:
k-1000
Explanation:
Answer:
k = 1;
total = 0;
do {
total = total + (k*k);
k++;
} while (k <= 50);
Explanation:
answer using Java
What are the 3 common ladder materials?
Answer:
Aluminium, Timber, Fibreglass
Explanation:
Most ladders are made of aluminium to have resistance against oxidisation and avoid rust; aluminium also doesnt spark either and is non magnetic. Some ladders are made out of timber like Douglas Fir, Oak, and Hickory. Some ladders are made out of fibreglass because it is strong and sturdy. They are also very to carry and are electrically resistant and heat tolerant.
could you put your sparkplug in the steering wheel and it still works
A. no
B. yes
C. do not care
D. it really doesn't matter
Answer:
a
Explanation:
Question #9
Multiple Choice
Which statement characterizes how the creation of LIMBS benefits developing countries?
O Using nanotechnology, a new material is created to benefit many other products
Using only natural materials, there is little chemical production, thus reducing the pollution in these countries
Using regional materials creates a sustainable program that breaks countries dependencies on other nations
Using fabricated materials, no natural resources are overfarmed, keeping the environment intact.
© 2014 Glynlyon, Inc.
Answer:
Using regional materials creates a sustainable program that breaks countries’ dependencies on other nations.
Explanation:
i did the assignment
Answer:
Using regional materials creates a sustainable program that breaks countries’ dependencies on other nations.
Explanation:
C
A single phase, 50-KVA, 2400-240-volt, 60 Hz distribution transformer has the following parameters: •
Resistance of the 2400-volt winding Ri=0.75 ohm
Resistance of the 240-volt winding R=0.0075 ohm
Leakage reactance of the 2400-volt winding X:=1 ohm
Leakage reactance of the 240-volt winding X2=0.01 ohm
Core loss resistance on the 2400 side Rc=733.5 ohms
Magnetizing reactance on the 2400 side X=4890 ohms
a. Draw the equivalent circuit referred to the high voltage side and referred to the low- voltage side. Label the impedances numerically.
b. The transformer is used as a step-down transformer at the load end of a feeder having impedance of (0.5+j2.0) ohms. Determine the voltage V. at the ending end of the feeder when the transformer delivers rated load at rated secondary voltage and 0.8 laggin power factor. Neglect the "exciting current" l. of the transformer (this is the current into the parallel Rc/jXm combination), which is another way of saying that you should use what we called in class the "approximate circuit #2).
Answer:
B) voltage at the sending end of the feeder = 2483.66 v
Explanation:
attached below is the the equivalent circuits and the remaining solution for option A
B) voltage = 2400 v
I = [tex]\frac{50*10^3}{2400}[/tex] = 20.83 A
calculate voltage at sending end ( Vs )
Vs = 2400 + 20.83 ∠ -cos^-1 (0.8) ( 0.75*2 + 0.5 + j 2 + j2 )
hence Vs = 2483.66 ∠ 0.961
therefore voltage at the sending end = 2483.66 v
Assignment 1: Structural Design of Rectangular Reinforced Concrete Beams for Bending
Perform structural design of a rectangular reinforced concrete beam for bending. The beam is simply supported and has a span L=20 feet. In addition to its own weight the beam should support a superimposed dead load of 0.50 k/ft and a live load of 0.65 k/ft. Use a beam width of 12 inches. The depth of the beam should satisfy the ACI stipulations for minimum depth and be proportioned for economy. Concrete compressive strength f’c = 4,000 psi and yield stress of reinforcing bars fy = 60,000 psi. Size of stirrups should be chosen based on the size of the reinforcing bars. The beam is neither exposed to weather nor in contact with the ground, meaning it is subjected to interior exposure.
• Use the reference on "Practical Considerations for Rectangular Reinforced Concrete Beams"
• Include references to ACI code – see slides from second class
• Include references to Tables from Appendix A
• Draw a sketch of the reinforced concrete beam showing all dimensions, number and size of rebars, including stirrups.
Answer:
Beam of 25" depth and 12" width is sufficient.
I've attached a detailed section of the beam.
Explanation:
We are given;
Beam Span; L = 20 ft
Dead load; DL = 0.50 k/ft
Live load; LL = 0.65 k/ft.
Beam width; b = 12 inches
From ACI code, ultimate load is given as;
W_u = 1.2DL + 1.6LL
Thus;
W_u = 1.2(0.5) + 1.6(0.65)
W_u = 1.64 k/ft
Now, ultimate moment is given by the formula;
M_u = (W_u × L²)/8
M_u = (1.64 × 20²)/8
M_u = 82 k-ft
Since span is 20 ft, it's a bit larger than the average span beams, thus, let's try a depth of d = 25 inches.
Effective depth of a beam is given by the formula;
d_eff = d - clear cover - stirrup diameter - ½Main bar diameter
Now, let's adopt the following;
Clear cover = 1.5"
Stirrup diameter = 0.5"
Main bar diameter = 1"
Thus;
d_eff = 25" - 1.5" - 0.5" - ½(1")
d_eff = 22.5"
Now, let's find steel ratio(ρ) ;
ρ = Total A_s/(b × d_eff)
Now, A_s = ½ × area of main diameter bar
Thus, A_s = ½ × π × 1² = 0.785 in²
Let's use Nominal number of 3 bars as our main diameter bars.
Thus, total A_s = 3 × 0.785
Total A_s = 2.355 in²
Hence;
ρ = 2.355/(22.5 × 12)
ρ = 0.008722
Design moment Capacity is given;
M_n = Φ * ρ * Fy * b * d²[1 – (0.59ρfy/fc’)]/12
Φ is 0.9
f’c = 4,000 psi = 4 kpsi
fy = 60,000 psi = 60 kpsi
M_n = 0.9 × 0.008722 × 60 × 12 × 22.5²[1 - (0.59 × 0.008722 × 60/4)]/12
M_n = 220.03 k-ft
Thus: M_n > M_u
Thus, the beam of 25" depth and 12" width is sufficient.
Type your response in the box. Most novels include at least one important symbol. Identify at least one symbol in the novel you just finished. In 125 to 150 words, identify the symbol. State the type of symbol it is (universal or contextual), and describe its meaning. Be sure to include specific details from the story to support your answer.
Answer:
Symbols in The Secret Garden:
The secret garden: The garden seems to be a symbol for Mary’s transformation. She changes from a sickly child to a healthy one. It is a contextual symbol.
The robin: The robin symbolizes the kindness and compassion of nature. The robin is a contextual symbol.
Spring: The spring season is a symbol for change and new life. It represents these ideas in each of the characters at the end of the story. It is a universal symbol.
Symbols in The Hunger Games:
Katniss’s mockingjay pin: It might stand for rebellion and resistance against the Capitol. It is a contextual symbol.
The mockingjay: The bird itself is a symbol for resistance against the Capitol. It is a contextual symbol.
Bread: It is a symbol for the connection between Katniss and Peeta. It is a contextual symbol.
Symbols in Hatchet:
The hatchet: The hatchet symbolizes survival and self-reliance. The hatchet is a contextual symbol.
The moose and the tornado: Both symbolize confusion and the power nature has over people. They are contextual symbols. However, a tornado can also be a universal symbol for destruction.
The plane: The plane symbolizes the changes in Brian’s life. It represents how Brian moves from one stage of his life to another. It is a contextual symbol.
Symbols in The Red Badge of Courage:
The dead soldier: The dead soldier symbolizes how all things will eventually end. It expresses the idea that accomplishments may mean very little. It is a universal symbol for an end.
Henry’s wound: For Henry, a wound symbolizes a soldier’s bravery at war. It is a contextual symbol.
Flag: A flag symbolizes the values and identity of a state or nation. It also represents the reason why two opposing sides of a war are fighting. A flag is a universal symbol.
Explanation:
These are the answers for Plato, these are the answers from each novel.
I hope this helps you!
The structure consists of a very large steel plate they will be used to transfer an in plane tensile stress. You have information from the company that performed a non-destructive testing technique if there are any flaws inside the plate. This non-destructive testing technique is based on ultrasonic wave transmission and will only detect a crack if it is bigger than 2.5 mm. No flaws were detected in the plate. You decided to pull some samples from a similar plate and you determined that the KIC value of these plates are 40 MPa*m0.5.
Required:
Estimate the maximum in plane tensile stress that you would suggest that this plate should carry.
Answer:
[tex]\mathbf{\sigma_{max} =638.308 \ MPa}[/tex]
Explanation:
For any large steel plate with an infinite length and width and a center through the crack under tension, the stress intensity factor can be expressed as:
[tex]K_I = \sigma \sqrt{\pi a}[/tex]
where;
a = 2.5 mm/2
a = 1.25 mm
a = 1.25 × 10⁻³ m
Therefore; the maximum stress in tension capacity can be computed as;
[tex]\sigma_{max} = \dfrac{K_{I_C}}{\sqrt{\pi a_c}}[/tex]
[tex]\sigma_{max} = \dfrac{40}{\sqrt{\pi \times 1.25 \times 10^{-3}}}[/tex]
[tex]\mathbf{\sigma_{max} =638.308 \ MPa}[/tex]
The site earthwork in Phase III of Four Hills Landfill project included a 3.0 ft deep cut across an entire 2.5-acre site. Soil was excavated from within the proposed Phase III footprint. The average unit weight of this soil is 118 lb/ft3, and the average moisture content is 9.6%. It also has a maximum dry unit weight of 122 lb/ft3 and an optimum moisture content of 11.1%, based on the modified Proctor test. The excavated soil will be placed on a nearby site and compacted to an average relative compaction of 93%. Compute the volume of fill that will be produced and express your answer in cubic yards.
Answer: 11470.4 cubic yards
Explanation:
first we calculate the volume of the site;
V1 = Area × depth
V1 = 2.5 acre × (43560 ft² / 1 acre )×3ft
V1 = 326700 ft
next we is the relative compaction
RC = [γd(field) / γdmax(laboratory)] × 100
so we substitute
93 = [γd(field) / 122 lb/ft³)] × 100
γd(field) = 113.46 lb/ft³
then the dry unit weight of the site
γday1 = γavg / ( 1 + w)
= 118 lb/ft³ / ( 1 + (9.6/100))
= 118 lb/ft³ /1.096
= 107.664 lb/ft³
finally we find the fill volume of the site
V2/V1 = γd / γd(field)
we substitute
V2/326700 = 107.664 / 113.46
V2 = 310010.83 ft³
we convert to cubic yards
= 310010.83 ft³ × (0.037 cubic yard / 1 ft³)
= 11470.4 cubic yards
PLZ HELP A person hired by a pharmaceutical company to streamline the company’s drug production process would most likely be an electrical engineer? True or False
Answer:
False
Explanation:
False, though they could do it.
It's most likely and Industrial Engineer, it could also be a Chemical Engineer.
Will give correct answer brainliest!!
Fill in the blank.
_________ are engineers who help to develop products and projects by creating technical drawings
Answer:
Design engineer
Explanation:
Do you consider the letter of Andres Bonifacio an eyewitness account of a firsthand account of the Philippine Revolution?
T.J. wants to send a friend a file with a funny dancing cat. Which file format should T.J. use?
DOCX
GIF
MP3
PDF
Answer:
T. J. should the file by GIF to his friend.
beeeeeeeeeeeeeeeeeeeeeeeeep its gif
The weight of your car will aslo affect its
Answer:
speed and acceleration
James is planning on registering for a course in electrical engineering. Which of the following sub-disciplines could he opt for?
Instrumentation engineering
Prosthetics
Plant design
Signal processing
Answer:
I hope this helps
Explanation:
Instrmentation engineering
Answer:
Instrumentation engineering
Explanation:
Design a U-tube manometer that can measure gage pressures up to 69 kPa of air. You will want to choose a manometer fluid with good static sensitivity but will not result in an unreasonably tall manometer. Further, the manometer fluid should be mostly immiscible with the air. The two design parameters you should consider are manometer fluid (impacts manometer fluid density) as well as the manometer height.
Required:
Compute the static sensitivity, K, in mmHg/Pa
Answer:
The answer "K = 0.0075"
Explanation:
If we try to measure up to 69 kPa of air, find mercury or fluid for gauge.
While mercury was its largest liquid with a density of 13600 kg / m3 at normal room temperature.
Let's all measure for 69 kPa that height of the mercury liquid column.
[tex]\to P = 69 \ kPa[/tex]
[tex]= 69000 Pa \\\\[/tex]
[tex]\to \rho = 13600 \ \ \frac{kg}{m^3} \\\\\\to g = 9.81 \ \ \frac{m}{s^2} \\\\[/tex]
Formula:
[tex]\to P=\rho \ gh[/tex]
[tex]\to 69000 = 13600\times9.81 \times h\\\\\to h= \frac{69000}{13600\times9.81} \\\\\to h= \frac{69000}{133416} \\\\\to h= 0.517179349 \\\\ \to h= 517 \ mm \\\\[/tex]
The right choice for pressure measurements up to 69 kPa is mercury.
Atmospheric Mercury up to 69 kPa Air 517 mm
The relationship of Hg to Pa is = 134.22 Pa 1 mm Hg
Static sensitivity to Pa of mm hg = change of mercury height to Pa:
[tex]= \frac{\Delta Hg }{ \Delta P }\\\\= \frac{1 }{ 133.3 }\\\\= 0.0075[/tex]
Mechanic... Mechanical Engineer... What's the difference?
Instructions: Answer the question below with at least TWO complete sentences.
Answer:
Mechanic: a person who repairs and maintains machinery
Mechanical engineers: design power-producing machines
Explanation:
technician A says that in any circuit, electrical current takes the path of least resistance. technician B says that while this is true in a series circuit, it's not entirely true in a parallel circuit. who is correct?
Answer:
technician A is correct
Explanation:
Technician B has circuit topologies confused. In a series circuit, there is only one path for electrical current to take. In a parallel circuit, the current will divide between paths in proportion to the inverse of their resistance. The least resistance path will have the most current.
Technician A is mostly correct.
A DC servomotor has a torque constant of 0.075 N-m/A and a voltage constant of 0.12 V/(rad/sec). The armature resistance is 2.5 Ohm. A terminal voltage of 24 V is used to operate the motor. Determine:
a) the starting torque generated by the motor just as the voltage is applied.
b) the maximum speed at a torque of zero.
c) the operating point of the motor when it is connected to a load whose torque characteristic is proportional to speed with a constant of proportionality = 0.0125 N-m/(rad/sec).
Answer:
The answer is below
Explanation:
Given that:
[tex]k_t=torque\ constant=0.075\ Nm/A\\\\k_v=voltage\ constant=0.12\ V/(rad/sec)\\\\R_a=armature \ resistance=2.5 \Omega\\\\V_t=terminal\ voltage=24\ V\\\\a)The \ starting\ current\ I_a\ is\ given \ as:\\\\I_a=\frac{V_t}{R_a} =\frac{24}{2.5} =9.6\ A\\\\The \ starting\ torque(T)\ is:\\\\T=k_tI_a=0.075*9.6=0.72\ N.m[/tex]
b) The maximum speed occurs when the terminal voltage and back emf are equal to each other i.e.
[tex]V_t=e_b=k_v\omega\\\\\omega=\frac{V_t}{k_v}=\frac{24}{0.12} =200\ rad/s[/tex]
c) The load torque is given as:
[tex]T_L=0.0125\Omega\\\\The\ motor\ torque \ is:\\\\T=k_t(\frac{V_t-k_v\omega}{R_a} )\\\\but\ T = T_L,hence:\\\\0.0125\omega=0.075(\frac{24-0.12\omega}{2.5} )\\\\0.03125\omega=1.8-0.009\omega\\\\0.04025\omega=1.8\\\\\omega=44.72\ rad/sec\\\\N=\frac{60\omega}{2\pi} =\frac{60*44.72}{2\pi} =427\ rpm[/tex]
A work cell is currently operated 2000 hr/yr by a human worker who is paid an hourly rate of $23.00, which includes applicable overhead costs. One work unit is produced in a cycle time of 4.8 min. Management would like to increase output to meet increasing demand and a robot cell is being considered as a replacement for the present manual cell. The cycle time of the proposed cell would be reduced to 4.0 min. The installed cost of the robot plus supporting equipment is $120,000. Power and other utilities to operate the robot will be $0.30/hr, and annual maintenance costs are $2500. Determine:
a. the number of parts produced annually by the manually operated cell.
b. cost per part produced.
c. how does the cost per part of the robot cell compare with your answer in part (b), given a 4-year service life, 10% rate of return, and no salvage value.
Answer:
a) 25000 pcs/yr
b) cost per part produced is $ 1.84 per pc
c) Cpc = $ 1.365 per pcs
Explanation:
a)
the relation to calculate the number of parts produced annually by manual process is;
Q = Hw / Tc
Hw is the hourly rate ( 2000hr/yr) and Tc is the cycle time ( 4.8 min)
so we substitute
Q = (2000 × 60) / 4.8
= 120000 / 4.8
= 25000 pcs/yr
b)
cost per part produced
the relation to calculate the cost per part produced is expressed as;
Cpc = $23(Hw) / Q
Cpc is the cost per part produced
so we substitute
Cpc = $23(2000) / 25000
= 46000 / 25000
= $ 1.8 per pc
therefore cost per part produced is $ 1.84 per pc
c)
for the robot cell, at a service life of 4 years and a 10% rate of return , the factor is expressed as;
f = [r(1 + r)^t] / [((1 + r)^t ) - 1 ]
our rate r = 10% = 0.1 and our t = 4
so we substitute
f = [0.1 (1 + 0.1)^4] / [((1 + 0.1)^4 ) - 1 ]
f = 0.14641 / 0.4641
f = 0.3155
now we find the total cost
TC = 120000(0.3155) + 2000(0.3) + 2500
TC = $ 40,960
next we find the parts produced annually
Q = (2000 × 60) / 4
Q = 120,000 / 4
Q = 30000 pcs/yr
finally we find the cost per part produced;
Cpc = TC / Q
we substitute
Cpc = 40,960 / 30000
Cpc = $ 1.365 per pcs
What kind of job does mike have? Mike’s job is to study blueprints, evaluate product stability, and to examine the safety of products. Mike’s works as a/n blank engineer with a manufacturing company.
Answer: a drafting engineer
Explanation:
If a water heater operates at 20 amps on a 240 volt circuit, what is the wattage of the appliance?
Answer:
4800 watts
Explanation:
Power is the product of voltage and current:
P = VI = (240 V)(20 A) = 4800 W
The wattage is 4800 watts.
Martha has been running a small business for two years. She now seeks additional investment to finance her business. She has found potential investors who want to check how much Martha's business owns and owes others. Which financial statement should Martha provide to her investors? A. cash flow statement B. balance sheet C. trial balance D. journal
Answer:
The correct option is B) Balance Sheet
Explanation:
A Balance Sheet offers a description of a company's obligations, assets, and investments as well as net income over a given span of time such as a period of 6 months or 12 months, for instance.
Also known as the Statement of Financial Position, it contains sufficient information for investors and business owners to determine the company's financial performance in that period as well as to compare the performance of that company with industry norms or competition.
Cheers