Design a Finite State Moore Machine (FSM) that will take an arbitrary-sized integer as input, one bit at a time (starting from most significant bit), and return the remainder after this integer is divided by 5. This is also called as MOD 5 function. For example if the input number is 34, then its binary representation will be 100010 and 34 MOD 5 will return 4 as an output.

Answer:fall arrest harness

Explanation:cuz it’s just right

Answer:

I’m sorry I don’t understand this is there more steps?‍♀️

Explanation:

Answer:

skate-themed video games

library research

interviews with skaters

documentaries on skater culture

(I got a 90% on the test so I dont  know if this was the one that gave me the 90% but it said it was right)

Answer:

3

Explanation:

it is compulsory to have a bachelor's degree

Answer: walk dog on leash for one and two you csnt park in a car you park the car and walk the dog on a leash

Explanation: did you phrase the question wrong?

Answer:

missing question; How long must the heated section be

answer : 5.898 meters

Explanation:

Given parameters:

Diameter of steel pipe = 1.5 inches = 0.0381 m

velocity of air = 2.10 ft/s = 0.64 m/s

Inlet temperature = 25°C

Outlet temperature = 95.5°C

pipe wall temperature = 121.1°C

Average temperature = ( 25 + 95.5 ) / 2 = 60.25°

determine Reynolds number of air at 60.25°

= VD / v = ( 0.64 * 0.0381 ) / ( 1.83 * 10^-5 )

              = 1332.46  this means the flow is laminar

hence mass flow rate ( m ) = eAv = 1.08 * πd^2 * velocity

= 1.08 * 0.0046 * 0.64 = 0.0032 g/s

attached below is the remaining part of the solution

Answer:

  entering drivers

Explanation:

Drivers entering a traffic circle must yield the right-of-way to those already in the traffic circle. (Among other things, this rule helps avoid gridlock.)

Answer:

Answer:

Solving

Explanation:

Answer

letter B is the answer because 7.5+7.5=15

The resistance of each of the bulbs will be 30 ohms. The correct option is D.

To resist the passage of current, use a resistor. When a resistor is included in a circuit, the amount of current that flows through it drops.

Using ohms as the unit, resistance acts as a gauge to quantify how easily current will flow through a circuit.

When resistance falls, current rises, and when resistance rises, current falls. In order to make sure that current flows in circuits at the proper rate, resistors are crucial.

Here, it is given that:

Total resistance is 15 ohms.

We know that, two identical resistors in parallel have an equivalent resistance half the value of either resistor.

So, the total resistance of 15 ohms have the resistance of each of the bulbs as 30 ohms.

Thus, the correct option is D.

For more details regarding resistance, visit:

https://brainly.com/question/29427458

#SPJ2

Answer:

- the force of the rope on the tugboat is 14.87 kN

- Force acting on the tugboat is 24.79 kN

Explanation:

 Given the data in the question;

tugboat increases its speed uniformly to 25 km/h

v₁ = 25 km/h = (25 × 1000) / ( 1 × 60min × 60sec )

= 25000m / 3600s

=  6.94 m/s

Now, lets determine the force on the rope using the following relation;

T = [tex]m_b[/tex]v₁ / t₁

[tex]m_b[/tex] is mass of barge( 75 Megagram = 75 × 10³ Kilogram  ), time t₁ is 35 s and v₁ is 6.94 m/s

so we substitute

T = [(75 × 10³) × 6.94 ]  / 35

T = 520500 / 35

T = 14871.43 N

T = 14871.43 / 1000

T = 14.87 kN

Therefore, the force of the rope on the tugboat is 14.87 kN

Now, to determine F acting on the tugboat;

[tex]Ft_1[/tex] = ( [tex]m_t[/tex] + [tex]m_b[/tex] )[tex]v_1[/tex]

we solve for F

F = ( [tex]m_t[/tex] + [tex]m_b[/tex] )[tex]v_1[/tex] / [tex]t_1[/tex]

where [tex]m_t[/tex] is mass of tugboat (50 Megagram = 50 × 10³ Kilogram  )

so we substitute

F = [( (50 × 10³) + (75 × 10³) )6.94] / 35

F = [ 125000 × 6.94 ) / 35

F = 867500 / 35

F = 24785.7 N

F = 24785.7 / 1000

F = 24.79 kN

Therefore, Force acting on the tugboat is 24.79 kN

Answer:

i) 25.04 W/m^2 .k

ii) 23.82 minutes = 1429.2 secs

Explanation:

Given data:

Diameter of steel ball = 15 cm

uniform temperature = 350°C

p = 8055 kg/m^3

Cp = 480 J/kg.k

surface temp of ball drops to  250°C

average surface temperature = ( 350 + 250 ) / 2 = 300°C

i) Determine the average convection heat transfer coefficient during the cooling process

Note : Obtain the properties of air at 1 atm at average film temp of 30°C from the table  " properties of air "  contained in your textbook

average convection heat transfer coefficient = 25.04 W/m^2 .k

ii) Determine how long this process has taken

Time taken by the process = 23.82 minutes = 1429.2 seconds

Δt = Qtotal / Qavg = 683232 / 477.92 = 1429.59 secs

attached below is the detailed solution of the given question

Answer:

  12.44Ω

Explanation:

For a question such as this, the assumption must be that the resistance is inversely proportional to the square of the diameter. The resistance will be ...

  20Ω × (1.262/1.6)² ≈ 12.44Ω

Answer:

[tex]ohms[/tex]

Explanation:

hope it helps

Answer:

Oxygen is an important part of the atmosphere and is necessary to sustain terrestrial life. Because it comprises most of the mass in water, it also comprises most of the mass of living organisms. All major classes of structural molecules in living organisms, such as proteins, carbohydrates, and fats, contain oxygen, as do the major inorganic compounds that comprise animal shells, teeth, and bone. Elemental oxygen (O2) is produced by cyanobacteria, algae, and plants through the process of photosynthesis, and is used in cellular respiration by most living organisms on earth. Oxygen is toxic to obligate anaerobic organisms (organisms which need a lack of oxygen for survival), which were the dominant form of early life on Earth, until O2 began to accumulate in the atmosphere.

Explanation:

Answer:

B is correct

Explanation:

Answer:

a) 15.075  , b ) 12.9

Explanation:

pressure on cylindrical vessel = 1.7 MPa

Twisting moment due to pressure = To of  8( 10^6 ) N-m

outer diameter of vessel = 2.5 m

wall thickness of vessel = 50 mm

Steel wall uniaxial yield strength = 600 MPa

Calculate the factor of safety

a) assuming a max shear stress yield criterion

safety factor = 15.075

b) assuming a von Mises yield criterion

safety factor = 12.9

attached below is the detailed solution of the problem

Answer:

Explanation:

Given that:

The Inside pressure (p) = 1402 kPa

= 1.402 × 10³ Pa

Force (F) = 13 kN

= 13 × 10³ N

Thickness (t) = 18 mm

= 18 × 10⁻³ m

Radius (r) = 306 mm

= 306 × 10⁻³ m

Suppose we choose the tensile stress to be (+ve) and the compressive stress to be (-ve)

Then;

the state of the plane stress can be expressed as follows:

[tex](\sigma_ x) = \dfrac{Pd}{4t}+ \dfrac{F}{2 \pi rt}[/tex]

Since d = 2r

Then:

[tex](\sigma_ x) = \dfrac{Pr}{2t}+ \dfrac{F}{2 \pi rt}[/tex]

[tex](\sigma_ x) = \dfrac{1402 \times 306 \times 10^3}{2(18)}+ \dfrac{13 \times 10^3}{2 \pi \times 306\times 18 \times 10^{-3} \times 10^{-3}}[/tex]

[tex](\sigma_ x) = \dfrac{429012000}{36}+ \dfrac{13000}{34607.78467}[/tex]

[tex](\sigma_ x) = 11917000.38[/tex]

[tex](\sigma_ x) = 11.917 \times 10^6 \ Pa[/tex]

[tex](\sigma_ x) = 11.917 \ MPa[/tex]

[tex]\sigma_y = \dfrac{pd}{2t} \\ \\ \sigma_y = \dfrac{pr}{t} \\ \\ \sigma _y = \dfrac{1402\times 10^3 \times 306}{18} \ N/m^2 \\ \\ \sigma _y = 23.834 \times 10^6 \ Pa \\ \\ \sigma_y = 23.834 \ MPa[/tex]

When we take a look at the surface of the circular cylinder parabolic variation, the shear stress is zero.

Thus;

[tex]\tau _{xy} =0[/tex]

Answer:

Hello the frequency response is missing attached below is the missing image

answer : Elliptic Filter

Explanation:

The filter with such frequency response that is an analog band-pass filter as well is called an Elliptic filter.

And this is because an Elliptic filter posses a constant ripple in the stop band and a unity gain is seen in the pass band

Answer:

A) Not possible, B) Posible, C) Possible, D) Not possible.

Explanation:

The maximum theoretical efficiency for any thermal engine is defined by Carnot's cycle, whose energy efficiency ([tex]\eta[/tex]), no unit, is expressed below:

[tex]\eta = 1-\frac{T_{L}}{T_{H}}[/tex] (1)

Where:

[tex]T_{L}[/tex] - Cold reservoir temperature, in Kelvin.

[tex]T_{H}[/tex] - Hot reservoir temperature, in Kelvin.

If we know that [tex]T_{L} = 250\,K[/tex] and [tex]T_{H} = 750\,K[/tex], then the maximum theoretical efficiency for the thermal engine is:

[tex]\eta = 1-\frac{T_{L}}{T_{H}}[/tex]

[tex]\eta = 0.667[/tex]

For real thermal engines, the following inequation is observed:

[tex]0 \le \eta_{r} \le \eta[/tex] (2)

Where [tex]\eta_{r}[/tex] is the efficiency of the real heat engine, no unit.

There are two possible criteria to determine if a given heat engine is real:

Efficiency

[tex]\eta_{r} = 1 - \frac{Q_{L}}{Q_{H}}[/tex] (3)

Where:

[tex]Q_{L}[/tex] - Heat rejected to the cold reservoir, in kilojoules.

[tex]Q_{H}[/tex] - Heat received from the hot reservoir, in kilojoules.

Power output

[tex]W = Q_{H}-Q_{L}[/tex] (4)

Where [tex]W[/tex] is the power output, in kilojoules.

Now we proceed to verify each case:

A) [tex]Q_{H} = 900\,kJ[/tex], [tex]Q_{L} = 600\,kJ[/tex], [tex]W_{m} = 400\,kJ[/tex]

[tex]\eta_{r} = 0.333[/tex]

[tex]0 \le \eta_{r} \le \eta[/tex]

[tex]W = 300\,kJ[/tex]

[tex]W \ne W_{m}[/tex]

This engine is not possible.

B) [tex]Q_{H} = 900\,kJ[/tex], [tex]Q_{L} = 500\,kJ[/tex], [tex]W_{m} = 400\,kJ[/tex]

[tex]\eta_{r} = 0.444[/tex]

[tex]0 \le \eta_{r} \le \eta[/tex]

[tex]W = 400\,kJ[/tex]

[tex]W = W_{m}[/tex]

The engine is possible.

C) [tex]Q_{H} = 900\,kJ[/tex], [tex]Q_{L} = 300\,kJ[/tex], [tex]W_{m} = 600\,kJ[/tex]

[tex]\eta_{r} = 0.667[/tex]

[tex]0 \le \eta_{r} \le \eta[/tex]

[tex]W = 600\,kJ[/tex]

[tex]W = W_{m}[/tex]

The engine is possible.

D) [tex]Q_{H} = 900\,kJ[/tex], [tex]Q_{L} = 100\,kJ[/tex], [tex]W_{m} = 800\,kJ[/tex]

[tex]\eta_{r} = 0.889[/tex]

[tex]\eta_{r} > \eta[/tex]

[tex]W = 800\,kJ[/tex]

[tex]W = W_{m}[/tex]

The engine is possible.

Answer:

24 i believe

Explanation:

Answer:

Ans: To see if the results are similar

Answer:

  a, c

Explanation:

As the problem statement tells you, the phasor technique cannot be used when the frequencies are different. The frequencies are different when the coefficients of t are different. The different ones are highlighted.

a. 45 sin(2500t – 50°) + 20 cos(1500t +20°)

b. 25 cos(50t + 160°) + 15 cos(50t +70°)

c. 100 cos(500t +40°) + 50 sin(500t – 120°) – 120 cos(500t + 60°) -100 sin(10,000t +90°) + 40 sin(10, 100t – 80°) + 80 cos(10,000t)

d. 75 cos(8t+40°) + 75 sin(8t+10°) – 75 cos(8t + 160°)

Answer:

Answer: True

Explanation: