how does increasing energy affect the amplitude of a wave?​

Answer:

c.an electron or positron

Answer:

your answer would be c

Explanation:

Answer:

$1.26

Explanation:

Power =energy/ time

energy =powerxtime

energy =50x31x24=37200

=37.2kwh

1kwh =3.39

37.2kwh=3.39x37.2=126.108cent

=$1.26

Answer:

11.25J

Explanation:

15=(output/75)x100

output =(75x15)/100=11.25J

Answer:

g = 11.2 m/s²

Explanation:

First, we will calculate the time period of the pendulum:

[tex]T = \frac{t}{n}[/tex]

where,

T = Time period = ?

t = time taken = 135 s

n = no. of swings in given time = 98

Therefore,

[tex]T = \frac{135\ s}{98}[/tex]

T = 1.38 s

Now, we utilize the second formula for the time period of the simple pendulum, given as follows:

[tex]T = 2\pi \sqrt{\frac{l}{g}}[/tex]

where,

l = length of pendulum = 54 cm = 0.54 m

g = acceleration due to gravity on the planet = ?

Therefore,

[tex](1.38\ s)^2 = 4\pi^2(\frac{0.54\ m}{g} )\\\\g = \frac{4\pi^2(0.54\ m)}{(1.38\ s)^2}[/tex]

g = 11.2 m/s²

Answer moderate alcohol can be good for you health

Explanation: but I wouldn't do none of those things to be honest

SMARTEST

Answer:

none of the above

Explanation:

its an easy question haha

Answer:

One degree unit on the Celcius scale is equivalent to one degree unit on the kelvin scale. The only difference between these two scales is the zero point. The zero point on the Celcius scale was defined as the freezing point of water, which means that there are higher and lower temperatures around it.

Answer:

A: Alpha decay.

Explanation:

The transmutation of ²³⁸U is a nuclear reaction that yields ²³⁴Th and an alpha particle.

Now, Alpha decay is a radioactive decay whereby an atomic nucleus emits an alpha particle which then changes into an atom with a mass number that is decreased by four and atomic number decreased by 2.

In this case, mass number is reduced from 238 to 234. Thus, it's an alpha decay.

Answer:

the speed of an object is 9.42 m/s

Explanation:

The computation of the speed of an object is given below:

v = 2πr ÷ t

where

v denotes the speed

r denotes the radius

r denotes the time

So,

= 2 × 3.14 × 0.75 ÷ 0.50

= 9.42 m/s

Hence, the speed of an object is 9.42 m/s

the same would be considered and relevant too

Complete question is;

Shoveling snow can be extremely taxing since the arms have such a low efficiency in this activity. Suppose a person shoveling a sidewalk metabolizes food at the rate of 800 W. (The efficiency of a person shoveling is 3%.)

(a) What is her useful power output? (b) How long will it take her to lift 3000 kg of snow 1.20 m? (This could be the amount of heavy snow on 20 m of footpath.) (c) How much waste heat transfer in kilojoules will she generate in the process?

Answer:

A) P_out = 24 W

B) t = 1470 s

C) Q = 1140.72 KJ

Explanation:

We are given;

Input Power; P_in = 800 W

Efficiency; η = 3% = 0.03

A) Formula for efficiency is;

η = P_out/P_in

Making P_out the subject, we have;

P_out = η•P_in

P_out = 0.03 × 800

P_out = 24 W

B) We know that;

Power = work done/time taken

Thus;

P_out = mgh/t

We are given;

m = 3000 kg

h = 1.20 m

Thus, time is;

t = (3000 × 9.8 × 1.2)/24

t = 1470 s

C) amount of heat wasted is calculated from;

Q = (P_in - P_out)t

Q = (800 - 24) × 1470

Q = 1,140,720 J

Q = 1140.72 KJ

Answer:

Hope this helps!  can I have brainliest im trying to level up.

Explanation:

Bumper cars are a great place to see Sir Isaac Newton’s three laws of motion in action. Here’s how:

Newton’s First Law: Every object in motion continues in motion and every object at rest continues to be at rest unless an outside force acts upon it.

This is because all objects have inertia – the property of matter that resists changes to the object’s motion.

Newton found that if a ball is sitting on a table, it will stay sitting there because that is what it ‘wants’ to do.

If the ball is set in motion, it will keep traveling in a straight path because, again, that is what it ‘wants’ to do.

An object in motion will not stop, slow down, or change its direction unless an outside force acts on it (such as gravity, friction, and air resistance).

When you are riding in a bumper car and end up in a collision with another bumper car, you feel a jolt. This is because your body’s inertia wants it to keep traveling in the direction it was moving with the car even though your bumper car has now suddenly stopped.

Newton’s Second Law: The greater the mass of an object, the harder it is to change its speed.

(More force is needed to move it.)

You already know this law and practice it in your everyday life. Something that is small, such as a pebble, is much easier to pick up and throw than something that is large and heavy, such as a boulder.

When riding in the bumper cars, you may have noticed that people who weigh less tend to get pushed around more than people who weigh more.

The more mass (weight) an object has, the more force it takes to move it.

And since all the bumper cars usually have the same top velocity, the cars carrying more mass will never travel as far as the cars carrying less mass after a collision.

Newton’s Third Law: For every action, there is an equal and opposite reaction.

If two bumper cars traveling at the same speed and carrying the same amount of weight run into each other, they will bounce off and move an equal distance away from each other.

And based on the second law, if there is a difference in the amount of weight being carried in the two cars, the car with less weight will travel farther away from the point of impact than the car carrying more weight.

Answer: I believe hydrogen cyanide, carbon monoxide, and ammonia are the three chemicals involved, but im not sure

Answer:

a. E = 900000 J = 900 KJ

b. ΔT = 8.18 °C

c. Cost = $ 7.2  

Explanation:

a.

The energy can be given by:

[tex]E = Pt[/tex]

where,

E = Energy = ?

P = Power = 500 W

t = time = (0.5 h)(3600 s/1 h) = 1800 s

Therefore,

[tex]E = (500\ W)(1800\ s)[/tex]

E = 900000 J = 900 KJ

b.

The change in temperature of room air is given by the following formula:

[tex]0.5E = mC\Delta T\\[/tex]   (since 50% of energy is used to heat air)

where,

m = mass of air = 50 kg

C = specific heat of air = 1.1 KJ/kg.°C

ΔT = Change in temperature of air = ?

Therefore,

[tex](0.5)(900\ KJ) = (50\ kg)(1.1\ KJ/Kg.^oC)\Delta T[/tex]

ΔT = 8.18 °C

c.

First, we will calculate the total energy consumed:

[tex]E = (0.5\ KW)(6\ h/d)(30\ d)\\E = 90\ KWh[/tex]

Now, for the cost:

[tex]Cost = (Unit\ Cost)(Energy)\\Cost = (\$ 0.08\KWh)(90\ KWh)[/tex]

Cost = $ 7.2

Answer: True!

Explanation: The force is proportional to the square of the distance between 2 point masses

Answer:

Wavelength = 0.66 meters

Explanation:

Given the following data;

Speed = 330 m/s

Frequency = 500 Hz

To find the wavelength;

Mathematically, wavelength is calculated using this formula;

[tex] Wavelength = \frac {speed}{frequency} [/tex]

Substituting into the equation, we have;

[tex] Wavelength = \frac {330}{500} [/tex]

Wavelength = 0.66 meters

Answer:

Explanation:

they trade velocities... so the Satellite now is going 5000 m/s  

Answer:

the current INCREASES.

Explanation:

In this experiment, the electrons are generated by a filament with very low speed, when they are subjected to a difference and potential ΔV they acquire the necessary speed to reach the regulation and the current can be measured.

Some electrons collide elastically with the atoms of the mercury gas that is much heavier and are scattered in any direction, so they do not reach the grid, by increasing the voltage this scattered electrons can acquire the necessary speed in the direction of grid to reach it and therefore are also measured, increasing the current.

Therefore, as the power difference increases, the current INCREASES.

62.5 m/s

Explanation:

Answer:

250w

Explanation:

W=Fd

W= 250 x 4= 1000J

P=E/t=1000/4s=250w

Answer:

Let's see the similarities between the two forces

* are proportional to the product of a magnitude, mass or charge

* They are inversely proportional to the square of the distance

* They are long-range forces since zero is not made up to an infinite distance. The gravitational force is always attractive, the electrical force can be attractive or repulsive.

The differences in them

* The electric force in much greater than the gravitational force

* The gravitational force is always attractive, the electrical force can be attractive or repulsive.

Explanation:

Let's start by calculating each force.

Gravitational force

             F =[tex]G \frac{m_1m_2}{r^2}[/tex]  

let's calculate

             F = 6.67 10⁻¹¹  1  1 / 1²

             F = 6.67 10⁻¹¹ N

Electric force

             F = [tex]k \frac{q_1q_2}{r^2}[/tex]  

indicates that the charge is q = 10 C

            F = 9 10⁹ 10 10 / 1²

            F = 9 10¹¹ N

Let's see the similarities between the two forces

* are proportional to the product of a magnitude, mass or charge

* They are inversely proportional to the square of the distance

* They are long-range forces since zero is not made up to an infinite distance. The gravitational force is always attractive, the electrical force can be attractive or repulsive.

The differences in them

* The electric force in much greater than the gravitational force

* The gravitational force is always attractive, the electrical force can be attractive or repulsive.

The moment of inertia of Pulley is 8.89 kgm².

The angular acceleration of the pulley is calculated as follows;

[tex]\alpha = \frac{\omega_f - \omega _i}{t}[/tex]

where;

Final angular velocity in radian per second is calculated as

[tex]\omega _f = 17 \frac{rev}{\min} \times \frac{2\pi \ rad}{1 \ rev} \times \frac{1\min}{60 \ s} = 1.78 \ rad/s[/tex]

Now, solve for angular acceleration

[tex]\alpha = \frac{1.78-0}{5} \\\\\alpha = 0.36 \ rad/s^2[/tex]

The the moment of inertia of Pulley is determined using the formula for torque.

Iα = Fr

I = Fr/α

I = (16 x 0.2)/(0.36)

I = 8.89 kgm²

Thus, the moment of inertia of Pulley is 8.89 kgm².

Learn more about moment of inertia here: https://brainly.com/question/25803184

Solution :

We know that the time period of oscillation of a spring mass system is given by :

[tex]$T = 2 \pi \sqrt{\frac{m}{k}}$[/tex]     , where m is mass and k is the spring constant

∴ [tex]$T_A = 2 \pi \sqrt{\frac{m}{k}}$[/tex]    .........(i)

  [tex]$T_B = 2 \pi \sqrt{\frac{2m}{k}}$[/tex] ..........(ii)

  [tex]$T_C = 2 \pi \sqrt{\frac{3m}{6k}} = 2 \pi \sqrt{\frac{m}{2k}}$[/tex]   ..........(iii)

  [tex]$T_D = 2 \pi \sqrt{\frac{m}{4k}}$[/tex]   ...............(iv)

Comparing the equations (i), (ii), (iii) and (iv)

We get

[tex]$T_B > T_A > T_C > T_D$[/tex]

So in increasing order of time period, we get

[tex]$T_D < T_C < T_A < T_B$[/tex]

Answer:

1.33

Explanation:

For an optical instrument, the magnification ratio of the apparent diameter of the image to that of the object.

Mathematically, from the given information;

Magnification[tex]= \dfrac{n_{water}}{n_{air}}[/tex]

where;

[tex]n_{water} =1.33\\ \\ n_{air} = 1.00[/tex]

[tex]= \dfrac{1.33}{1.00} \\ \\= \mathbf{1.33}[/tex]

Answer:

Either heat added or mechanical work done.

Explanation:

Since he found stirring rod on the desk and a cigarette lighter. This means that the beaker was probably either heated with the aid of fire from the lighter.

Also, the stirring rod could have been used to stir the water which will increase the kinetic energy which also means an increase in temperature.

Thus, it's either heat was added or mechanical work was done as a result of stirring.

The release of infrared light from radioactive materials is what demonstrates light possessing wave characteristics.

This is defined as the propagation of disturbances from one place to another in an organized way.

The release of waves in a diffraction pattern is why option C was chosen as the most appropriate choice.

Read more about Wave here https://brainly.com/question/15663649

Answer:

B. Attract each other with a force of 10 newtons.

Explanation:

Statement is incorrectly written. The correct form is: A [tex]+10\,\mu C[/tex] charge and a [tex]-10\,\mu C[/tex] at a distance of 0.3 meters.

The two particles have charges opposite to each other, so they attract each other due to electrostatic force, described by Coulomb's Law, whose formula is described below:

[tex]F = \frac{\kappa \cdot |q_{A}|\cdot |q_{B}|}{r^{2}}[/tex] (1)

Where:

[tex]F[/tex] - Electrostatic force, in newtons.

[tex]\kappa[/tex] - Electrostatic constant, in newton-square meters per square coulomb.

[tex]|q_{A}|,|q_{B}|[/tex] - Magnitudes of electric charges, in coulombs.

[tex]r[/tex] - Distance between charges, in meters.

If we know that [tex]\kappa = 8.988\times 10^{9}\,\frac{N\cdot m^{2}}{C^{2}}[/tex], [tex]|q_{A}| = |q_{B}| = 10\times 10^{-6}\,C[/tex] and [tex]r = 0.3\,m[/tex], then the magnitude of the electrostatic force is:

[tex]F = \frac{\kappa \cdot |q_{A}|\cdot |q_{B}|}{r^{2}}[/tex]

[tex]F = 9.987\,N[/tex]

In consequence, correct answer is B.

Answer:

The work done will be "763 J". A further explanation is given below.

Explanation:

The given values are:

[tex]Q_1=1000 \ J[/tex]

Temperature,

[tex]T_1=900^{\circ} C[/tex]

i.e,

    [tex]=1173[/tex]

[tex]T_2=5^{\circ}C[/tex]

i.e.,

    [tex]=278[/tex]

As we know,

⇒  [tex]\eta =1-\frac{T_2}{T_1}[/tex]

On substituting the values, we get

⇒     [tex]=1-\frac{278}{1173}[/tex]

⇒     [tex]=\frac{1173-278}{1173}[/tex]

⇒     [tex]=\frac{895}{1173}[/tex]

⇒     [tex]=0.763[/tex]

then,

⇒  [tex]W=\eta Q_1[/tex]

⇒       [tex]=0.763\times 1000[/tex]

⇒       [tex]=763 \ J[/tex]

Answer:

32km per hour

Explanation:

Explanation:

In first case v = a t

==> a t = 40 km p h

Now distance covered S1 + S2 + S3

S1 = 1/2 a t^2 and S3 = 1/2 a t^2

But S2 = 3t * 40 = 120 t km

Hence total distance = at^2 + 120 t

Time taken (total) = t + 3t + t = 5 t

Hence average speed = at^2 + 120 t / 5 t

Cancelling t we have at + 120 / 5 = 40 + 120 / 5 = 160/5 = 32 km per hour

Explanation:

V= Current × Resistance

V= 400mA × 5kohms

V= 2000V