Answer:
The first one.
If the road becomes wet or crowded, you should ___ slow down and increase your following distance_
What is meant by surface distance ?
The safe distance between vehicles traveling in column specified by the command in light of safety requirements
The slower speed will help you save gas and avoid potential accidents. You can easily eliminate chances of rear end collision by maintaining a safe distance between your car and the vehicles ahead.
hence , a) slow down and increase your following distance is a correct option
learn more about safe distance
https://brainly.com/question/4144073?referrer=searchResults
#SPJ2
A rocket burns fuel at a rate of 239 kg/s
and exhausts the gas at a relative speed of
6 km/s.
Find the thrust of the rocket.
Answer in units of MN.
The Thrust on the rocket is 1.434 MN.
To calculate the thrust of a rocket, we use the formula below
Thrust: This is the force that moves an aircraft through the air.
⇒Formula
T = M'×v.................... Equation 1⇒ Where:
T = Thrust of the rocketM' = Fuel ejection ratev = gas exhaust velocityFrom the question,
⇒ Given:
M' = 239 kg/sv = 60 km/s = 6000 m/s⇒ Substitute these values into equation 1
T = 239(6000)T = 1434000 NT = 1.434 MNHence, the Thrust on the rocket is 1.434 MN.
Learn more about Thrust here: https://brainly.com/question/13501791
c. Two persons A and B are pushing a block from opposite sides with
force of 5N and 6N respectively.
[3]
i) Find the magnitude of the resultant force on the block.
ii) Find the direction of resultant force with respect to A and B.
Answer:
1 N
Explanation:
1) You'll just have to sum the force vectors, and since they are opposite, you'll calculate the difference of their magnitudes, in absolute value.
Ftot = |F1 - F2| = 6N - 5N = 1N
2)The direction will be the same as the greater force's direction.
Which best describes how plant and animal cells carry out the basic functions of life?
A.
Plant and animal cells do not need food molecules for growth.
B.
Plant and animal cells do not make molecules for their own growth and repair.
C.
Plant and animal cells break down food for growth and repair.
D.
Plant and animal cells perform life functions such as making food molecules for growth.
Why doesn't the skater ever regain his potential energy?
Answer:
Friction
Explanation:
As the skateboarder goes down the ramp, potential energy is converted to kinetic energy. Because of friction, some of the energy in the system is converted to heat energy. Once the kinetic energy is converted to heat, the energy cannot be converted back to the potential or kinetic energy in the system.
PLEASE HELP-I LITERALLY NEED THIS RIGHT NOW!!! I'LL GIVE BRAINLIEST AND 5 STARS!!!!!!!!!!!!!!!!
why has the number of islands in hawaii increased over the last 100 million years
Answer: oceanic crust moved over the hot spot, each recently formed volcano was carried away from the hot spot toward the northwest, cutting off its source of lava. Meanwhile, a new island was forming so that over time a chain of islands was produced extending away from the hot spot.ANSWER HERE: This mean that volcanos are producing these new islands and it is creating a chain of different islands all over Hawaii.
Answer:
Oceanic crust moved over the hot spot, each recently formed volcano was carried away from the hot spot toward the northwest, cutting off its source of lava. Meanwhile, a new island was forming so that over time a chain of islands was produced extending away from the hot spot.
The gravitational potential energy of a cucumber-harth system changes when which factor changes?
A) the cucumber's speed
B) the cucumber's mass
c) the cucumber's temperature
D) the length
A bike accelerates uniformly from rest to a speed of 7.10 m/s over a distance of 35.4 m. Determine the acceleration of the bike.
So acceleration of the bike which started from rest, reaches at speed of 7.10 m/s by travelling distance 35.4 m will be 0.712 m/ sec^2.
The app claimed it has "Forbidden text"
how to solve for time given distance and velocity
Answer:
Well, I think you're talking about kinematics, especially uniform rectilinear motion. We know that there is a specific equation for that:
S = Vt + S0
With S being the distance, V the velocity, t the time and S0 the initial distance (initial displacement).
From this you can calculate t, if that's what you want.
Which metals can be extracted from following ores (i) Argentite (ii) Haematite (iii) Chalcopyrite (iv) Bauxite
I hope it's helpful for you ☺️
1) iron
2) aluminium
3) silver
4) copper
A 263 g ball of clay falls onto a vertical spring.
The spring constant k = 2.52 N/cm.
The clay sticks to the spring and as the spring compresses a distance of 11.8 cm the clay momentarily comes to rest.
Determine the speed of the clay just before it hit the spring in [m/s]?
As the spring is compressed, it performs
-1/2 (252 N/m) (0.118 m)² ≈ -1.75 J
of work on the clay, while gravity does
(0.263 kg) (9.80 m/s²) (0.118 m) ≈ 0.304 J
on it. Then the total work W performed on the clay ball is approximately -1.45 J.
By the work-energy theorem, W is equal to the change in the clay ball's kinetic energy ∆K. If v is the speed with which it hits the spring, then
W = ∆K
-1.45 J = 0 - 1/2 mv²
Solve for v :
-1.45 J = -1/2 (0.263 kg) v²
v² ≈ 11.0 m²/s²
v ≈ 3.32 m/s
what planets experience an eclipse from the sun
Answer:
Earth
Explanation:
The sun and the moon come together and they seem like one bonded.
how much power is needed to lift a box with a force of 780 newtons over a distance of 2 meters in 45 seconds
Answer:
34.67 WExplanation:
Power is the rate at which work is done and can be found by using the formula
[tex]p = \frac{w}{t} \\ [/tex]
p is the power in Watts (W)
w is the workdone in joules
t is time in s
but workdone = force × distance
From the question
force = 780 N
distance = 2 m
workdone = 780 × 2 = 1560 N
Since we now have the value of workdone we can find the power
We have
[tex]p = \frac{1560}{45} = 34.6666666... \\ [/tex]
We have the final answer as
34.67 WHope this helps you
Draw a nitrogen cycle and explain in short.
please help me
Answer: biogeochemical process
Explanation:
Which type of circuit would be best to use for lights used for decorations?
Answer:
led would be the best for decorations
Explanation:
A dog is pulling an empty sled attached by a harness that is parallel to the
ground in the snow. The sled is moving with constant velocity. The mass of
the sled is 1.2 kg, and the coefficient of static friction is 0.20. Determine the
harness tension.
Answer:
Explanation:
There are only two forces causing motion involved. They oppose each other. You know this because there is no acceleration of the sled: you see only a velocity.
The formula when friction is involved is
Fnet = T - mu*Normal
mu is the frictional coefficient
The normal is the downward force caused by the mass of the sled being pulled down by the gravitational constant.
The tension is brought about by the dog pulling in the opposite direction to the frictional force.
The frictional force, oddly, acts in a horizontal direction even though the normal is vertical. It does this because friction always opposes motion.
Since there is no acceleration, the net force = 0
N= m * a_g
m = 1.2 kg
a_g = 9.8
N = 1.2 * 9.8
N = 11.76
The frictional force = mu*Normal Force.
Ff = N * mu
N = 11.76
mu = 0.2
Ff = 0.2 * 11.76
Ff = 2.35
As stated The frictional force and the Tension are equal but in opposite directions
T = 2.35
A cheetah runs at an average speed of 60mph. find the distance it runs in 30 s
Answer:60mph means it runs every minute.
Explanation: because it makes sense.
Answer:
2640 ft, or 1/2 mile
Explanation:
Recognizing that 30 s = 0.5 min, we can convert the units like this.
distance = speed × time
distance = (60 mi/h) × (1 h/(60 min)) ×(0.5 min) = 0.5 mi
In feet, that is ...
(5280 ft/mi)(0.5 mi) = 2640 ft
A cheetah runs 1/2 mile, or 2640 feet in 30 s.
HELP!!!!!!!!!!!!
9. Estimate the change in the thermal energy of water in a pond with a mass of
1000 kg and a specific heat of 4200 J/(kg. C) if the water cools by 1°C.
Answer:
-4,200,000 J
Explanation:
in what direction will the seesaw rotate and what will the sign of the angular acceleration be?
Answer:
It can rotate in any direction. The sign of the angular acceleration depends on how you set the reference system, it can be both negative or positive.
the normal formula to find force is F = m*a. What kind of math do you need to do
to find the mass of an object?
- Divide: F / a
- Divide: a / F
- Multiply: F* a
- Subtract: F - a
[tex]\\ \sf\Rrightarrow F=ma[/tex]
Take a to leftAs it's multiplied on right side it will be divided on right side.[tex]\\ \sf\Rrightarrow \dfrac{F}{a}=m[/tex]
Or
[tex]\\ \sf\Rrightarrow m=\dfrac{F}{a}[/tex]
A projectile with an initial velocity of 48 feet per second is launched from a building 190 feet tall. The path of the projectile is modeled using the equation h(t) = â€""16t2 48t 190. Approximately when will the projectile hit the ground? 1. 5 seconds 3. 2 seconds 5. 3 seconds 6. 2 seconds.
The time for the projectile to hit the ground from the given position is 1.5 s.
The given parameters:
Initial velocity of the projectile, u = 48 ft/sHeight, h = 190 ftModel of the projectile path, h(t) = –16t² + 48t + 190.The time for the projectile to hit the ground is calculated as follows:
when the projectile hits the ground, the final velocity = 0
[tex]v_f = 0\\\\\frac{dh(t)}{dt} = v_f\\\\\frac{dh(t)}{dt} = -32t + 48\\\\-32t+48 = 0\\\\32t = 48\\\\t = \frac{48}{32} \\\\t = 1.5 \ s[/tex]
Thus, the time for the projectile to hit the ground from the given position is 1.5 s.
Learn more about time of motion of projectiles here: https://brainly.com/question/13533552
Which of the following is an example of physical weathering?
O calcium carbonate in limestone changes to calcium hydrogen carbonate
O flow water carves erosion channels in a hillside
Ostalactites precipitate in a cave
O acid rain corrodes a monument
Answer:
acid rain corrodes a monument. d.
Explanation:it only makes sense because its doing something to a physical object.and the other ones aren't.
Help please I will mark you the brainly!
D)
Explanation:
Coz the position changes with time but the position change is not constant throughout time So, D) does not have constant velocity
The strings in a compound bow behave approximately like a
spring. A bowstring is pulled back 0.60 m with a maximum force of
267 N (AKA a 60-pound draw weight) to shoot an 18 g arrow.
Assume energy is conserved.
a) At what speed would the arrow be launched? (Note: W = FΔd uses the average
force while F = -kx uses the instantaneous force.)
The speed at which the arrow would be launched is 133.42 m/s
The work-energy theorem asserts that the net work done applied by the forces on a particular object is equivalent to the change in its kinetic energy.
The equation for the work-energy theorem can be computed as:
[tex]\mathbf{W =\Delta K.E}[/tex]
[tex]\mathbf{F\Delta x =\dfrac{1}{2} mv^2}[/tex]
where;
Force (F) = 267 Ndistance Δx = 0.60 mmass (m) = 18 gspeed (v) = ???From the above equation, let make speed(v) the subject of the formula:
∴
[tex]\mathbf{v = \sqrt{\dfrac{2(F \Delta x)}{m}} }[/tex]
[tex]\mathbf{v = \sqrt{\dfrac{2(267 \times 0.60)}{0.018}} }[/tex]
v = 133.42 m/s
Learn more about the work-energy theorem here:
https://brainly.com/question/17081653
what is the electric field strength at a distance of .50 m from a 1.00x10^-6 c charge?
Answer:
e = k q / r² then,
e = 9×10^9 * 1×10^-6 / 50² = 3.6 N/C
hope this helps ❤.
A bullet of mass 20 g has its kinetic energy equal to 400 J. Find the speed of the bullet.
Answer:
m=20g=0.02kgK.E=400J[tex]\\ \sf\longmapsto KE=\dfrac{1}{2}mv^2[/tex]
[tex]\\ \sf\longmapsto \dfrac{1}{2}(0.02)v^2=400[/tex]
[tex]\\ \sf\longmapsto 0.01v^2=400[/tex]
[tex]\\ \sf\longmapsto v^2=40000[/tex]
[tex]\\ \sf\longmapsto v=200m/s[/tex]
A heating curve is a graph that shows the temperature change of a substance as
thermal energy is introduced.
True
False
Answer:
This statement is true, a heating curve is a graph that shows the temperature change of a substance as thermal energy is introduced.
A heating curve is a graph that represents the temperature change of a substance as thermal energy is introduced.
What is the heating curve?The heating curve can be described as the relationship between the heating supply temperature and the outside air temperature of the system. The heating curve gives what temperature the boiler is to heat the water at an outdoor temperature.
Heating curves indicate how the temperature changes as a substance are heated up. Cooling curves are generally the opposite of the heating curve. They indicate how the temperature changes as a substance are cooled down. Similar to heating curves, cooling curves have horizontal parts where the state transforms from gas to liquid/ from liquid to solid.
The heating curve represents the material in phases of solid, liquid, and gas. As this graph is a plot of T v/s q, the slope is 1/mC. As the heating continues, the solid substance melts. During this time the temperature remains constant. The length of the line can be described as the amount of heat required to melt the solid.
Learn more about the heating curve, here:
https://brainly.com/question/27018999
#SPJ2
1. A block with a mass of 5.0 kg is pushed on a frictionless surface by applying a horizontal force of 80.0 N. The block starts from rest, and its final velocity is 12.6 m/s.
Answer:
397 j
Explanation:
Because 5.0kg yuh
The kinetic energy of the block with a mass of 5.0 kg is pushed on a frictionless surface by applying a horizontal force of 80.0 N. The block starts from rest, and its final velocity is 12.6 m/s is 396.9 J.
What is kinetic energy?A moving item or particle has a certain kind of power called kinetic energy. When an item exerts a net force to perform work, which involves the transfer of energy, the object accelerates and as a result, gains kinetic energy.
The amount of kinetic energy that a moving object or particle possesses is determined by both its mass and rate of motion. Any combination of vibration, axis rotation, translation (or movement along a path from one location to another), and translation are all possible motion types.
Given:
The mass of the block, m = 5 kg,
The horizontal force, F = 80 N,
The velocity of the block, v = 12.6 m / s,
Calculate the kinetic energy by the formula given below,
[tex]KE = 1/2mv^2[/tex]
KE = 1 / 2 × 5 × 12.6²
KE = 1 / 2 × 5 × 158.6
KE = 396.9 J
Therefore, the kinetic energy of the block with a mass of 5.0 kg is pushed on a frictionless surface by applying a horizontal force of 80.0 N. The block starts from rest, and its final velocity is 12.6 m/s is 396.9 J.
To know more about Kinetic energy:
https://brainly.com/question/999862
#SPJ2
The complete question is A block with a mass of 5.0 kg is pushed on a frictionless surface by applying a horizontal force of 80.0 N. The block starts from rest, and its final velocity is 12.6 m/s. Find its kinetic energy?
a car dealer sells 4 makes of cars in 5 colors with either standard or automatic transmissions. how many variations does the dealership offer?
The number of variations the dealership have is 40 cars.
Data given;
The number of different product = 4The number of transmission = 2 (standard or automatic)The numbers of colors available = 5Dealership variationThis is the total numbers of cars available in the dealer shop at the moment.
To get that, we simply multiply the numbers of colors available, the number of transmission and the makes of car available.
This is equal to
[tex]4*2*5=40[/tex]
From the above calculation, we can say that the variations the dealership offers is 40
Learn more on combination here
https://brainly.com/question/10339517
When an object is balanced about a pivot, the total clockwise moment must be equal to the total __________ __________. What two words complete this sentence?
Answer:
When an object is balanced, about a pivot, the total clockwise moment must be equal to the total anticlockwise moment about that pivot.
Hope that helps.
When an object is balanced about a pivot, the total clockwise moment must be equal to the total anticlockwise moment.
What is balancing?
Clockwise involves turning to the right while going in the direction of a clock's hands. The moment is referred to as a clockwise moment if the force acting on a body rotates the body clockwise with regard to the axis of rotation.
On the other hand, the moment is referred to as an anti-clockwise moment if the force rotates the body in the opposite direction. The clock face rule can be used to determine this magnet's polarity.
The face of the loop will display the North Pole if the current is flowing counterclockwise. On the other hand, if the current is moving counterclockwise, the South Pole is visible on the loop's face.
Therefore, the total clockwise and total counterclockwise moments must match when an object is balanced about a pivot.
To learn more about balancing, refer to the link:
https://brainly.com/question/21414123
#SPJ2